News

  • 0
  • 0

Production and Applications of Naphthalene Sulfonate Water Reducing Agent

Russian president demanded that exports of Russian gas to "unfriendly" countries be settled in rubles. The demand has raised concerns in Germany about possible supply disruptions and the impact on industry and households if utilities do not pay in robles. Europe gets about 40% of its gas from Russia. Last year, Europe imported about 155 billion cubic meters. Germany, Europe's largest economy, depends heavily on Russian gas.

The chief executive of Germany's E.ON said the German economy would face "significant damage, which should be avoided if possible" without Russian supplies. He also said it would take Germany three years to wean itself off Russian gas.  

In the event of a supply disruption, Germany's gas network regulator would prioritize home heating over industrial use, so energy-hungry manufacturers such as steelmakers would be the first to suffer, he said.

The volatile international situations will continue to affect the markets and prices of many commodities like the Water Reducing Agent.

Introduction to Naphthalene Sulfonate Water Reducing Agent:

It is the product of naphthalene sulfonated by sulfuric acid and then condensed with formaldehyde, which belongs to an anionic surfactant. The appearance of this kind of water-reducing agent depending on different products is light yellow to dark brown powder. It is soluble in water and has a good dispersing effect on many powder materials such as cement. The water reduction rate is 25%.

 

Preparation method of Naphthalene Sulfonate Water Reducing Agent:

The synthetic route of naphthalene sulfonate superplasticizer is as follows:

naphthalene → sulfonation → hydrolysis → condensation → neutralization → filtration → drying → product 

The raw material for production is naphthalene. First, the sulfonation reaction is carried out with concentrated sulfuric acid. The mole ratio of naphthalene to sulfuric acid is 1:1.3-1.4.  The reaction temperature was 160 - 165 and the reaction time was 3h.  Then the reactants were cooled to 120 for hydrolysis. At this time, naphthalene sulfonic acid was stable, while naphthalene sulfonic acid was easy to hydrolyze, thus reducing the amount of naphthalene sulfonic acid to facilitate the next polycondensation reaction. The hydrolysis time was about 30min. The condensation reaction is an important reaction in the production of a naphthalene sulfonate water reducer. At a certain temperature, the sulfonated naphthalene was condensed with formaldehyde to form a polymer compound. This reaction strongly affects the performance of the product.  In order to find the optimal process parameters, the effects of condensation time, condensation temperature, and the ratio of formaldehyde and naphthalene on product properties were investigated by means of uniform design.  The optimal temperature condition is 104. The optimal reaction time was 6h.  The optimal condition of formaldehyde dosage is 0.75. The maximum expected theoretical value is 18.3. 

 

Industrial production process of Naphthalene Sulfonate Water Reducing Agent:

(1) naphthalene: Naphthalene is solid at room temperature, and it is necessary to put naphthalene into the naphthalene kettle for heating and melting. 

(2) sulfonation: The sulfonation process is to add concentrated sulfuric acid to the sulfonation kettle and react with it to produce naphthalene sulfonic acid.  There are two types of naphthalene sulfonic acid: α -naphthalene sulfonic acid and β -naphthalene sulfonic acid. 

(3) hydrolysis: As α -naphthalene sulfonic acid is produced in the sulfonation reaction, its presence is not conducive to the condensation reaction, so it needs to add water to hydrolyze α -naphthalene sulfonic acid. 

(4) condensation: After the end of hydrolysis reaction to condensation kettle drop formaldehyde, and β -naphthalene sulfonic acid reaction to generate naphthalene sulfonated formaldehyde condensation. 

(5) neutralization: After condensation, the material enters the neutralization kettle, drops liquid alkali, neutralizes the excess sulfuric acid in the sulfonation reaction, and stops dropping when the PH reaches 7-9. 

The control system mainly monitors the production status of four different reaction reactors and their batching tanks. The production line can also carry out four production lines at the same time. Taking production line A as an example, there are one naphthalene reactor, two sulfonation reactors, four condensation reactors, and one neutralization reactor. Each reaction kettle has a feed valve, discharge valve, emptying valve, hot oil valve, cooling water valve, steam pressure valve, flush valve, etc., the reaction kettle with a raw material tank, two sulfonated kettles shared a sulfuric acid tank, every two condensation kettles would be equipped with a set of formaldehyde tank and dilution tank, each condensation kettle has a hydrolysis tank, liquid alkali tank to neutralize the alkali added drops in the kettle.

 

Applications of Naphthalene Sulfonate Water Reducing Agent:

Naphthalene water-reducing agent is a kind of concrete additive invented by Dr. Hwab Kenichi in Japan in 1962. It is a kind of chemical synthetic product of naphthalene sulfonate formaldehyde condensation, with industrial naphthalene, concentrated sulfuric acid, formaldehyde, and alkali as the main raw material. Adding a naphthalene water-reducing agent to concrete can not only improve the strength of concrete but also improve its various properties, such as wear resistance, corrosion resistance, permeability resistance, etc. Therefore, naphthalene water-reducing agent is widely used in roads, bridges, tunnels, docks, civil buildings, and other industries.

 

Suppliers of Concrete Additives

TRUNNANO is a reliable concrete additives supplier with over 12-year experience in nano-building energy conservation and nanotechnology development. If you are looking for high-quality concrete additives, please feel free to contact us and send an inquiry. (sales@cabr-concrete.com)

We accept payment via Credit Card, T/T, West Union, and Paypal. Trunnano will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.


A preparation developed in China; the comfort and the multifunctional properties of nanomaterials make "dead skin" capable of sensing again. Electronic skin is artificial skin that mimics the function of human skin. Recently, the world-renowned journal Advanced Science reported a simple and highly programmable electronic skin on a leather substrate developed by a Chinese team, which combines the natural complex structure of leather, the comfort of wearing, and the multi-functional properties of nanomaterials. , so that the "dead skin" has the ability to sense again.

In the future, Water Reducing Agent will be used in various high-tech fields, and the market demand for Water Reducing Agent will also be great. Please contact us for more information on Water Reducing Agent.


Inquery us

Our Latest News

What material is high borosilicate? Use of high borosilicate glass

US President recently decided to invoke a Cold War-era defense law to encourage domestic sodium aluminium silicate. 1. High borosilicate glass has a very low coefficient of thermal expansion, which is only about one-third of that of ordin…

What is the scope of application of zinc stearate emulsion?

Water-based zinc stearate mainly uses zinc stearate special additives, sandpaper polishing paint, thermal paper sensitizer functional additives, rubber and water-based paint release agents, etc.…

Action principle of boron nitride

The secretary general of the Organization of Petroleum Exporting Countries (OPEC) said recently that US economic sanctions against Venezuela have affected global energy supplies. He told Venezuelan media that the ECONOMIC sanctions imposed by the Uni…